hvac
Furnace Replacement Cost in Massachusetts Without the Old Rebates
Furnace replacement cost in Massachusetts often runs $5,000 to $13,000. See prices by fuel and efficiency, oil-to-gas costs, and current Mass Save rebate rules.
In This Article
- Approximate Installed Prices by Fuel and Efficiency
- How Prices Differ in Boston, Worcester, and Springfield
- Oil to Gas: What the Quote Should Include
- Permits and Licenses in Massachusetts
- Where Mass Save and Heat Pumps Fit In
- Reasons to Replace Now or Wait
- Questions Massachusetts Homeowners Ask About Furnaces
Furnace Replacement Cost in Massachusetts Without the Old Rebates
Mass Save no longer offers standard rebates for new natural gas, oil, or propane furnaces, and the federal 25C tax credit ended for equipment placed in service after December 31, 2025. So when a furnace quote lands in your inbox this winter, the number on the page is close to what you'll pay. Most Massachusetts homeowners should expect roughly $5,000 to $13,000 installed, depending on fuel, efficiency, and how much of the old system has to change.
Income-eligible households are the exception on rebates, and heat pump incentives remain large. Those two facts change the math for some homes, which is why it pays to look past the sticker price. Below are approximate price ranges by furnace type, along with the piping, venting, and permit issues that tend to move the final number.
Approximate Installed Prices by Fuel and Efficiency
A standard replacement means swapping a furnace of the same fuel with existing ductwork and venting that can be reused or simply adapted. Quotes vary among contractors by thousands of dollars, in part because installed labor in Greater Boston costs more than it does farther west. Treat these as planning figures, then collect at least three written estimates.
| Furnace type | Approximate efficiency | Approximate installed cost |
|---|---|---|
| Gas, standard | 80% AFUE | $4,000 to $7,000 |
| Gas, condensing | 90% to 96% AFUE | $5,500 to $10,000 |
| Gas, variable speed and modulating | 96% to 98% AFUE | $8,000 to $13,000 |
| Oil | 83% to 87% AFUE | $6,000 to $11,000 |
| Propane, condensing | 90% to 96% AFUE | $6,000 to $10,500 |
A condensing furnace needs PVC venting and a condensate drain, so a switch from an 80 percent unit can add about $500 to $2,000 in labor and materials. That work can get pricier in finished basements or row-style layouts without an easy exterior wall. Ask about the vent location before you choose a model, since it can decide what the job costs.
High-efficiency units usually pay back faster with gas prices at Massachusetts levels, especially in a drafty older house with a long heating season. A house running a 96 percent model instead of an 80 percent one would burn about one-sixth less gas for the same heat. Whether that's worth an extra $2,000 to $4,000 depends on your annual bill and how long you plan to stay.
How Prices Differ in Boston, Worcester, and Springfield
Boston and its inner suburbs usually land toward the top of these ranges. Tight basements, parking, permit logistics, and higher labor costs all play a role, and triple-deckers can mean a long carry down narrow stairs. A condensing gas furnace that runs $8,000 in Worcester might come in closer to $9,500 to $11,000 in Somerville or Dorchester.
Worcester generally sits in the middle. Plenty of its homes have gas service and older duct systems, so duct repairs often come up during a replacement. Cold winters on the hills there also make correct sizing important, and a heat loss calculation is worth asking for.
Springfield and the Pioneer Valley often come in somewhat lower, sometimes by around 5 to 15 percent. Competition among contractors varies more out here, so you may find fewer bids in smaller towns. Getting a quote from a company based in the next town over can widen your options.
Ductwork can move the total more than the furnace
Sealing and repairing ducts might add about $500 to $2,500, and a full replacement can run $3,000 to $8,000 or more. Older homes often have undersized returns, which cause noise and short equipment life no matter how good the furnace is. Ask for static pressure readings as part of the estimate, and be skeptical of anyone who won't take them.
Adding air conditioning at the same time
Many homeowners replace the furnace and central AC together, since the indoor coil and blower have to match. A combined project often runs about $9,000 to $15,000 or more around Boston. The bundled labor can save money compared with doing two separate jobs a few years apart.
Oil to Gas: What the Quote Should Include
Switching from oil starts with a call to the gas utility, since not every street has a main in front of the house. National Grid, Eversource, Berkshire Gas, and other Massachusetts utilities each have their own process for a new service, and the cost and timeline depend on your location. Ask for the service line answer in writing before you buy a furnace built for a fuel you may not be able to get.
The furnace itself is only one line. A conversion may also need interior gas piping at about $500 to $2,000, a chimney liner or new direct venting at about $500 to $3,000, and removal of the old oil tank at about $500 to $3,000. An underground tank costs more and may bring testing requirements, so tell the contractor what you have early on.
Oil tank removal in Massachusetts generally runs through the local fire department, and a permit may be needed, so check with your town before work begins. All told, an oil-to-gas switch can reach about $9,000 to $18,000. A high-efficiency oil furnace can be the cheaper path in the short term if the home has no gas line nearby, or if you expect to go to a heat pump in a few years.
Permits and Licenses in Massachusetts
Gas work here requires a permit, and it has to be done by a plumber or gas fitter licensed in Massachusetts. Boston's permitting office says only a contractor with a valid state trade license can apply for a gas permit. Sheet metal permits for flue or vent work may be separate, and rules vary from city to city.
Oil-fired equipment has its own path, with local fire officials commonly inspecting heating systems under state fire code. Your installer should pull the right permits and schedule any inspections. If a contractor suggests skipping a permit to save a little money, take that as your cue to call the next name on your list.
Permit fees are usually modest, often around $50 to $300, though they vary by town and job value. A permitted job leaves a record that can help during a future home sale. Ask to see the final inspection sign-off before you make the last payment.
Where Mass Save and Heat Pumps Fit In
Mass Save's site says rebates, incentives, and financing for natural gas, oil, and propane equipment are no longer available, except that income-eligible households can get incentives for upgrading existing fossil fuel equipment to high-efficiency models. If your income might qualify, make the program your first phone call, because it could cover a large portion of the work. Those programs also offer no-cost options in some cases.
For most households, the money now sits with heat pumps. Equipment installed during 2026 can qualify for a whole-home rebate of $2,650 per ton, up to $8,500, or a partial-home rebate of $1,125 per ton if a furnace stays as backup. For equipment installed on or after January 1, 2027, those rates drop to $2,350 and $1,000 per ton, with a $7,500 cap, and 2026 rebate forms must be received by February 28, 2027.
Whole-home eligibility has its own requirements, including using the heat pump as the sole heating and cooling source, a contractor from the Heat Pump Installer Network, and a sufficiently weatherized home. Keeping a gas furnace often means the smaller partial-home rebate. Check current terms with Mass Save before signing, as these programs have changed repeatedly.
Federal help is gone for now. Section 25C was terminated by the One Big Beautiful Bill Act, signed in July 2025, for property placed in service after December 31, 2025, so a contractor quoting a tax credit on a furnace installed this winter has it wrong. Ask a tax professional if you have questions about a project finished in 2025.
To plan the rest of your home budget, browse our Massachusetts homeowner cost guides for related repairs. For bids, start with the Massachusetts HVAC contractors in the directory and request written heat loss calculations.
Reasons to Replace Now or Wait
A cracked heat exchanger, a carbon monoxide concern, or a repair above about a third of the replacement cost usually pushes the decision toward replacing now. A furnace past roughly 15 to 20 years with rising repair bills is also a sensible candidate. Getting ahead of a failure lets you choose a date and compare bids, which often saves more than any seasonal sale.
Late spring and early fall are usually easier times to book. In January, you may have to accept the first available installer and whatever equipment is in stock. If yours is still running, get quotes now, and you'll have a plan if it quits during a cold snap.
Questions Massachusetts Homeowners Ask About Furnaces
How long does a furnace replacement take?
A like-for-like swap often takes a single day, while a conversion from oil to gas can take several days across multiple trades. Gas utility scheduling may add weeks, especially during the construction season. Ask for a realistic start date when you get your quote.
Is a 96 percent furnace worth it in Massachusetts?
Often, yes, particularly in homes burning a lot of gas each winter. Compare the added cost, commonly $1,500 to $4,000, against your current gas bills and how many years you plan to stay. The vent location and condensate drain can change that math in older homes.
Does Mass Save pay for a home energy assessment?
Mass Save offers no-cost home energy assessments, and those can point to air sealing and insulation work. Tightening up the house first may let you buy a smaller, less expensive furnace. Ask about it before you finalize equipment sizing.
Can I keep my oil furnace and add a heat pump?
Yes, many homes do, and it may qualify for the partial-home rebate if the integrated control and other program rules are met. Check the switchover temperature requirements with your installer. A setup like this often makes sense in a home with a fairly new oil unit.